Go Back   Alberta Outdoorsmen Forum > Main Category > Fishing Discussion

Reply
 
Thread Tools Display Modes
  #1  
Old 10-05-2018, 10:02 AM
pikergolf's Avatar
pikergolf pikergolf is offline
 
Join Date: Nov 2008
Posts: 11,285
Default transducer sealant question

I want to permanently mount my transducer. This involves a couple of sheet metal screws thru my aluminum transom. What is the recommendation for a sealant, and do I just apply it to the screw and screw in? Thanks.
__________________
“One of the sad signs of our times is that we have demonized those who produce, subsidized those who refuse to produce, and canonized those who complain.”

Thomas Sowell
Reply With Quote
  #2  
Old 10-05-2018, 10:14 AM
dodgeboy1979's Avatar
dodgeboy1979 dodgeboy1979 is offline
 
Join Date: Jul 2012
Location: Lloydminster Alberta
Posts: 1,297
Default

i just pre drill the hole, then add some clear silicon or marine goop into the holes prior to putting the screws in. Then just whip off the excess silicon that comes out.
Reply With Quote
  #3  
Old 10-05-2018, 10:17 AM
Big Sky's Avatar
Big Sky Big Sky is offline
 
Join Date: Feb 2012
Posts: 2,295
Default

Some silicone behind something like this.

https://www.cabelas.ca/product/10099...mounting-plate

If you are frugal, you wouldn't be the first guy to use a piece of treated wood.
Reply With Quote
  #4  
Old 10-05-2018, 10:24 AM
honker_clonker honker_clonker is offline
 
Join Date: Sep 2009
Posts: 387
Default

I'd also recommend getting the mounting plate, and using a pile of marine silicone to seal it.
Reply With Quote
  #5  
Old 10-05-2018, 12:08 PM
oilngas oilngas is offline
 
Join Date: Dec 2008
Posts: 1,024
Default

I would suggest a dense plastic mounting bracket glued to transom with the proper adhesive / sealant. Any Industrial plastic / adhesive store should be able to supply both. If you are coming by SE Calgary I can give you a piece of plastic and the adhesive (assuming it is still pliable and I can find it!!!).

The big advantage is that if you change sounders, mount transducer in wrong spot, damage transducer, tear it off on beaching etc. you can make changes without any holes in transom.
Reply With Quote
  #6  
Old 10-05-2018, 12:32 PM
huntsfurfish huntsfurfish is offline
 
Join Date: Apr 2009
Location: Southern Alberta
Posts: 7,350
Default

3m 4200 Marine and a mounting plate if someday you may want to remove it.

3m 5200 Marine and a mounting plate if you do not ever intend to remove it.

Already been said if you mount a plate you can move or add transducers(good advice).

Can get 3m marine at Canadian Tire.

4200 has 1 in stock in Medicine Hat.
5200 has 6 in stock in Medicine Hat.

https://www.cabelas.ca/product/10099...mounting-plate

Shows in stock.

And you can also add a couple screws if you wish.

PS - I used a couple of screws plus the 4200 and it was still not easy to get off after I got the screws out.
__________________
.
eat a snickers


made in Alberta__ born n raised.


FS-Tinfool hats by the roll.

Last edited by huntsfurfish; 10-05-2018 at 12:46 PM.
Reply With Quote
  #7  
Old 10-06-2018, 07:27 AM
Habfan's Avatar
Habfan Habfan is offline
 
Join Date: Sep 2013
Location: Calgary
Posts: 1,721
Default

Quote:
Originally Posted by pikergolf View Post
I want to permanently mount my transducer. This involves a couple of sheet metal screws thru my aluminum transom. What is the recommendation for a sealant, and do I just apply it to the screw and screw in? Thanks.
Marine Goop is the best. A small blob over the hole before you put the screws in, assuming you are pre drilling. If not, around the screw head after.
Reply With Quote
  #8  
Old 10-06-2018, 08:37 AM
-JR- -JR- is offline
 
Join Date: May 2007
Location: Edm.
Posts: 4,836
Default

If you are storing this boat out side or just under cold storage.
The transducer may fail if the temp. drops below -40 c
I now remove my transducer ever year from my boat.
Reply With Quote
  #9  
Old 10-06-2018, 08:47 AM
dodgeboy1979's Avatar
dodgeboy1979 dodgeboy1979 is offline
 
Join Date: Jul 2012
Location: Lloydminster Alberta
Posts: 1,297
Default

Quote:
Originally Posted by -JR- View Post
If you are storing this boat out side or just under cold storage.
The transducer may fail if the temp. drops below -40 c
I now remove my transducer ever year from my boat.
Your transducer must of got bumped, cracking the plastic when cold.
Reply With Quote
  #10  
Old 10-06-2018, 09:34 AM
fish99's Avatar
fish99 fish99 is offline
 
Join Date: Feb 2009
Location: pigeon lake
Posts: 1,570
Default

i used a puck board same material as hockey rink boards glued it to the transom of the crestliner mount transducer with screws just in the puck board no need to drill holes in boat that will eventually leak . it has be a few years now and no problems
Reply With Quote
  #11  
Old 10-06-2018, 11:31 AM
-JR- -JR- is offline
 
Join Date: May 2007
Location: Edm.
Posts: 4,836
Default

Quote:
Originally Posted by dodgeboy1979 View Post
Your transducer must of got bumped, cracking the plastic when cold.
I have lost two because of the cold and i know a few other guys also that got broken.
Its been a few years since it got below -40
Just not taking any more chances
Reply With Quote
  #12  
Old 10-08-2018, 01:25 PM
EZM's Avatar
EZM EZM is offline
 
Join Date: Jul 2010
Location: Edmonton
Posts: 11,851
Default

Like others have said - I strongly recommend mounting a plastic/marine board to the transom area where you intend to mount your transducer.

The plate mounts with a couple small screws and some marine sealant/glue like 5200 3M.

I've used 5200 on numerous applications below the waterline on numerous boats and have never had so much as a single drop of water in there. It creates a permanent waterproof seal.

At some point you will either want to adjust your transducer location or height and likely change out and/or upgrade your transducer and securing into a board (and not drilling more holes into your boat) is the way to go.

Do it once - do it right. Don't poke any more holes in your transom than you need to.
Reply With Quote
  #13  
Old 10-09-2018, 03:19 PM
TROLLER TROLLER is offline
 
Join Date: Dec 2011
Location: Rocky View County AB.
Posts: 3,550
Default

I picked up a small solid plastic type material plate at Bass. Came with a 2 part epoxy that was very easy to work with , no holes drilled into the boat, just the plate. Went on easy and holds like it was screwed on. Best of all no drilling into the boat. Cost was around 40 bucks.
Reply With Quote
  #14  
Old 10-09-2018, 04:34 PM
bobalong bobalong is offline
Banned
 
Join Date: May 2007
Posts: 4,130
Default

Buy a plastic cutting board or puckboard mount the board vertical with transducer bolted to the cutting board. You only drill a couple holes on the top of the board in the overwash area but the transom. No need to drill holes below the water line.
Reply With Quote
  #15  
Old 10-09-2018, 04:59 PM
pikergolf's Avatar
pikergolf pikergolf is offline
 
Join Date: Nov 2008
Posts: 11,285
Default

I was ready to dismiss the mounting board idea as I cannot see ever moving the transducer and it would require holes anyway. But I did some snooping and there was a guy that epoxied the mounting board to the transducer. It would be smart to have a board there just in case. He cut key's in the board with a dremel. I have a key cutting bit for my router table and am thinking of cutting some key's in a cutting board cut to size and epoxying it to the transducer. Thoughts?
__________________
“One of the sad signs of our times is that we have demonized those who produce, subsidized those who refuse to produce, and canonized those who complain.”

Thomas Sowell
Reply With Quote
  #16  
Old 10-09-2018, 05:10 PM
bobalong bobalong is offline
Banned
 
Join Date: May 2007
Posts: 4,130
Default

Buy a plastic cutting board or puckboard mount the board vertical with transducer bolted to the cutting board. You only drill a couple holes on the top of the board in the overwash area by the transom. No need to drill holes below the water line.
Reply With Quote
  #17  
Old 10-09-2018, 08:47 PM
EZM's Avatar
EZM EZM is offline
 
Join Date: Jul 2010
Location: Edmonton
Posts: 11,851
Default

Quote:
Originally Posted by pikergolf View Post
I was ready to dismiss the mounting board idea as I cannot see ever moving the transducer and it would require holes anyway. But I did some snooping and there was a guy that epoxied the mounting board to the transducer. It would be smart to have a board there just in case. He cut key's in the board with a dremel. I have a key cutting bit for my router table and am thinking of cutting some key's in a cutting board cut to size and epoxying it to the transducer. Thoughts?
You won't know if you need to move the transducer until you have mounted it and taken the boat out for a spin.

Keep in mind it's not uncommon to have to move it higher/lower or left/right to get consistent readings. To me, to risk drilling yet another 2-3 holes in your transom to re-position your transducer when you could have used a board is senseless.

Also, what happens a few years down the road when you upgrade your fish finder and need a different transducer?

Or what happens if you smack your transducer and it bends the screws and opens up your holes?

I'd say, and I'd insist, you buy the $20 board.....and do it right. Friends don't let friends do it wrong.

Keep in mind - with a board all you need are screws the correct length to penetrate the board but not too long as to pierce your transom. There will never be a need to drill another hole in your transom - and, as other have mentioned, you can glue it on or use a longer board and screw it above the water line.
Reply With Quote
  #18  
Old 10-11-2018, 04:51 AM
Kim473's Avatar
Kim473 Kim473 is offline
 
Join Date: Jan 2010
Location: Edmonton
Posts: 6,470
Default

You may want to change the transducer sometime, add another fish finder and a second one. Glue the board on then screw to it.
__________________
Kim

Gonna get me a 16" perch.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 02:24 AM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.