|
02-20-2018, 08:26 PM
|
|
|
Join Date: Mar 2014
Location: Edmonton
Posts: 1,051
|
|
Transmission Jack (Edmonton)
Throwout bearing went on my Jeep and managed to drop the transmission using a floor jack but putting it back in the next couple of days once I change the clutch and pilot bearing, don't really want to use a floor jack as it would require a lot of work lining it up.
Anyone have a transmission jack I could rent for a day or two or know of a place that rents them? Can't really justify spending $250+ on one for a single use. And don't want to do the buy and return as I think it is unethical.
Or if anyone has any tips to getting it back on using a floor jack that doesn't involve too much swearing.
|
02-20-2018, 10:45 PM
|
|
|
Join Date: Jul 2017
Posts: 1,425
|
|
Oh man, great workout, especially for an older fellow. My last one was the auto in my exploder. My technique with the floor jack is to build a 2x4 base that sets the trans angle while giving a level point over the CG to rest on the hoist. I slide the Tran under, then using 2x4 blocks, see saw it up into the hump. Once high enough, slide the jack and wood base under to complete the hoist. One hand to steady the trans, other runs the jack. When you get close to home the trans is contained in the hump, so it just becomes position and assist to slide it home. Make sure to pilot your friction plate if you had done any work there.
|
02-20-2018, 10:50 PM
|
|
|
Join Date: Nov 2014
Location: Sherwood Park, AB
Posts: 743
|
|
Check at Princess auto, I think they used to sell a transmission adapter plate that would work on a regular floor jack.
|
02-20-2018, 11:29 PM
|
|
|
Join Date: Oct 2014
Location: West Kelowna B.C.
Posts: 410
|
|
Man I remember laying in the dirt pulling my Borg warner automatic transmission out of my 1961 Zodiac onto my chest, then off me onto the dirt to be able to change the engine rear oil seal which was the old rope seal, had to use a Chinese finger to take out and then pull new one in.
Then squeeze back under and work trans onto me and work it back into place, the things you can do when young!
|
02-20-2018, 11:41 PM
|
|
|
Join Date: Nov 2014
Location: Sherwood Park, AB
Posts: 743
|
|
Quote:
Originally Posted by Kristopher10
Check at Princess auto, I think they used to sell a transmission adapter plate that would work on a regular floor jack.
|
Here is the link.
https://www.princessauto.com/en/deta...ck/A-p8667891e
Sent from my iPhone using Tapatalk
|
02-21-2018, 01:24 AM
|
|
|
|
Join Date: Aug 2007
Location: Calgary
Posts: 19,420
|
|
Tool rental shops might well have such an item available.
__________________
"The trouble with people idiot-proofing things, is the resulting evolution of the idiot." Me
|
02-21-2018, 04:58 AM
|
|
|
Join Date: Aug 2008
Location: Edmonton
Posts: 1,190
|
|
I did the clutch in my jeep TJ twice and it wasn't too bad using a floor jack. I used a ratchet strap to hold the tranny to the jack but kept it loose enough that I could still move it around to line everything up. The worst part was having to crawl under the darn thing. I told myself if I ever had to do it a third time I'd rent a shop bay with a vehicle lift for a day. If you need a clutch alignment tool I have one you can borrow.
|
02-21-2018, 05:12 AM
|
|
|
|
Join Date: Oct 2009
Location: Sherwood Park Ab
Posts: 6,282
|
|
330k on the Jeep Wrangler sitting in our garage right now. Hope reading this thread didn’t jinx us! Good luck with your install..
__________________
An awful lot of big game was killed with the .30-06 including the big bears before everyone became affluent enough to own a rifle for every species of game they might hunt.
|
02-21-2018, 02:45 PM
|
|
|
Join Date: Mar 2009
Location: Edmonton
Posts: 127
|
|
I think Partsource rents them out
|
02-21-2018, 03:33 PM
|
|
|
|
Join Date: Dec 2008
Location: Alberta
Posts: 24,071
|
|
I wish you were closer, I would just put you up on the 4 post lift
__________________
Only dead fish go with the flow. The rest use their brains in life.
Originally Posted by Twisted Canuck
I wasn't thinking far enough ahead for an outcome, I was ranting. By definition, a rant doesn't imply much forethought.....
|
02-21-2018, 07:02 PM
|
|
|
|
Join Date: Aug 2012
Location: Northeast of Edmonton
Posts: 427
|
|
The last one I did for my brother was an older ford half ton
Some times it’s just as easy to hand bomb it if it isn’t a steel case and 300lbs
Helps to have a helper push on it while you’re starting the bolts
That transmission adapter from PA sounds like a good idea too, I might have to pick one up.
Have input seal to do one day on my truck, and I’m not benching a 4L60
"Shuuuuuuussssshhhhh.
You can't post stuff like that, too many heads will explode."
Hillbillyreefer
|
02-21-2018, 08:21 PM
|
Banned
|
|
Join Date: May 2007
Location: YEG
Posts: 9,981
|
|
masalma has exceeded their stored private messages quota and cannot accept further messages until they clear some space.
|
02-22-2018, 06:38 AM
|
|
|
Join Date: Mar 2014
Location: Edmonton
Posts: 1,051
|
|
Quote:
Originally Posted by RandyBoBandy
masalma has exceeded their stored private messages quota and cannot accept further messages until they clear some space.
|
Sorry just cleaned up my. Inbox. Got the throw out bearing replaced. Just have to slap on the new pilot bearing and clutch. Need to pick up a bearing puller on the way home.
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -6. The time now is 01:22 PM.
|