Go Back   Alberta Outdoorsmen Forum > Main Category > Guns & Ammo Discussion

Reply
 
Thread Tools Display Modes
  #1  
Old 10-27-2017, 08:25 PM
outdoorguy outdoorguy is offline
 
Join Date: Feb 2009
Posts: 76
Default Reloading .308 Win

I ve picked up a T3 compact in .308 and have been trying to get an accurate load out of it with no consistent success. I have been using fired, tumbled, chamfered, trimmed Rem brass, Fed 210 primer, 46 gr Varget , 165 Nosler ballistic tip and OAL is 2.81. Does any one have some loads that have been accurate with their 308 that you would be willing to share.
I may also switch to 150 gr accubonds as in what I have been reading that appears to be a popular one for hunting.....
Can anyone help out with some information.

Thanks All!
Reply With Quote
  #2  
Old 10-27-2017, 08:38 PM
ruger300's Avatar
ruger300 ruger300 is offline
 
Join Date: Jun 2007
Posts: 493
Default

My daughters 308 in a Rem 760 shoots all 150 gr bullets 1" or better at 100 yds. It seems to be the bullet weight for her rifle.
Use Varget in that load as well.
Reply With Quote
  #3  
Old 10-27-2017, 08:53 PM
50BMG 50BMG is offline
 
Join Date: Oct 2017
Location: Northern Alberta
Posts: 42
Default

Your first issue might be that brass you're using. Upgrade that and you might see better results. Other than that, here is a load I use on my PGW Coyote.

Barrel length: 24"
Brass: Lapua
Primer: CCI BR2
Powder: Varget 47.2gr
Bullet: Lapua Scenar 155gr
Ogive OAL: 2.230" .007" jump (MY RIFLE, NOT YOURS)
Velocity: 2903fps 5 shot average S.D.=5 E.S.=10

Start low and work your way up. This load is 1/3moa out to 1300m.

EDIT: btw, this is not a hunting load.
Reply With Quote
  #4  
Old 10-27-2017, 09:09 PM
buck12 buck12 is offline
 
Join Date: Apr 2017
Posts: 28
Default 308 reload

My 308 likes 150 grain(hornady btsp) and I use IMR 4895/ 44.0 grains. nice group @200 yards. Simple but effective
Reply With Quote
  #5  
Old 10-27-2017, 09:13 PM
hogie hogie is offline
 
Join Date: Feb 2015
Location: Millet
Posts: 854
Default

I use 130gr ttsx up to 178gr amax bullets in multiple rifles. All will shoot well if I can find the right load. Varget and IMR 4895 are the powders I use.

If I'm struggling with getting accuracy with my handloads I will buy some factory match ammo to try. If that won't shoot then I'm looking at other issues. 308 is nice because lots of options available.

I've had a couple of rifles that really took some time and experimentation to find what reloads will work. Always been able to get results .
Reply With Quote
  #6  
Old 10-27-2017, 09:15 PM
tasco's Avatar
tasco tasco is offline
 
Join Date: Mar 2011
Location: Cayley
Posts: 72
Default

I am also working on a load for my .308 BLR takedown. It is a challenge trying to find out what a gun likes. Attached is a load test that I did for my BLR. I haven't had time yet to check out the two best velocity nodes. But if you have access to a chronograph, this may be a very fast way for you to come up with a good starting point or load to test. I have posted this graph in another thread. You don't need to go in .3 grain increments like I did. .5 grains should be more than adequate.
Attached Files
File Type: pdf BLR 308 Load Test.pdf (381.3 KB, 47 views)
Reply With Quote
  #7  
Old 10-27-2017, 10:33 PM
260 Rem 260 Rem is offline
 
Join Date: Nov 2009
Location: East Central Alberta
Posts: 8,315
Default

I don’t know if I should be offering any advice on 308 loads given that I am currently having a terrible time getting accuracy out of a newly chambered Bartlein barrel that to date has failed to produce a single 1/2” group at 100M
I should try 50BMG’s recipe given his stellar results (1\3MOA @ 1000 yds tops International Benchrest Nationals results.)

I have shot a fair amount of 308 out to my hunting comfort zone of 300M so don’t worry about loading hot. I suggest you start at 41.5 gr Varget and work up in .5 gr increments.
I have almost always found a sweet spot at about 42.0 grs with both 155 and 168 gr bullets... and often, another at about 44.0 grs.
If your barrel is telling you it doesn’t like a particilar bullet, it is time try something else.

Last edited by 260 Rem; 10-27-2017 at 10:39 PM.
Reply With Quote
  #8  
Old 10-27-2017, 10:46 PM
propliner propliner is offline
 
Join Date: Dec 2009
Posts: 1,309
Default

Try some Accurate 2230 powder with some 155gr Hornady bullets. I shot three groups of five in a row that all measured under 1/2". It is the best load I've fired in anything, ever. This was in a factory LTR with a good trigger.
Reply With Quote
  #9  
Old 10-27-2017, 10:55 PM
qwert qwert is offline
 
Join Date: Jan 2012
Posts: 2,443
Default

Quote:
Originally Posted by tasco View Post
I am also working on a load for my .308 BLR takedown. It is a challenge trying to find out what a gun likes. Attached is a load test that I did for my BLR. I haven't had time yet to check out the two best velocity nodes. But if you have access to a chronograph, this may be a very fast way for you to come up with a good starting point or load to test. I have posted this graph in another thread. You don't need to go in .3 grain increments like I did. .5 grains should be more than adequate.
While your graphing is good, the results are not definitive, but I suspect indicate possible nodes @~2725 & 2815 and perhaps 2850 fps, and possible high pressure or inconsistent combustion @ 45.4gr.
It would be helpful to have the POI drops @ 300 yds for these shots. They might provide additional information on the effect of velocity and pressure on your rifle's barrel harmonics and POI.
The inability of a Magnetospeed to collect both velocity and accurate POI drop for every shot is exactly why I do not use one.

Audette's suggested increment is .5%, or in your case .227gr.
If loading with a lab quality 'magnetic force restoration scale' then I would try .25gr increments, but for ease of loading I usually use .3gr for 308W.
I suspect that a .2gr increment is unlikely to provide much additional usable information, but that a .5gr increment is likely to miss significant indications.

The BLR can be a challenge for load development.
The barrel is not 'free floating' and can have quite different barrel harmonics than a typical bolt action.
A takedown is seldom as consistent as one solidly attached to the receiver.
The BLR action lacks the closing force of a bolt action and require more resizing and shoulder bump for reliable feeding than a typical bolt action.
The triggers tend to be less than target quality and will also reduce consistency and precision.
IMHE they are fine rifles and can be very accurate with a bullet it likes.
IIRC my BLR 308W has a barrel twist of 1-12, and tends to shoot more precisely with a shorter bullet like a 150 or 165gr.

I suggest you continue testing and collection of results data.


Good Luck, YMMV.

Last edited by qwert; 10-27-2017 at 11:00 PM.
Reply With Quote
  #10  
Old 10-27-2017, 11:10 PM
skidderman skidderman is offline
 
Join Date: Dec 2009
Location: Spruce Grove, AB
Posts: 3,039
Default

Browning BLR 308 using 165 grain nosler partitions, RL15 powder and Federal primers. Shoots lights out.
Reply With Quote
  #11  
Old 11-01-2017, 09:56 AM
abhunter8's Avatar
abhunter8 abhunter8 is offline
 
Join Date: Sep 2007
Location: Drayton Valley, AB
Posts: 699
Default

Tikka T3 .308:
RL15 44gr
Fed Brass
CCI primer
Nosler accubond 165gr.
Attached Images
File Type: jpg .308.jpg (9.1 KB, 111 views)

Last edited by abhunter8; 11-01-2017 at 10:18 AM.
Reply With Quote
  #12  
Old 11-01-2017, 11:27 AM
vic1 vic1 is offline
 
Join Date: May 2007
Posts: 254
Default

Try Hornady 150 gr SST with the same components. My T3 with 18.5" barrel shoots them very well.
Reply With Quote
  #13  
Old 11-01-2017, 11:33 AM
dogslayer403's Avatar
dogslayer403 dogslayer403 is offline
 
Join Date: Jul 2010
Location: Rocky Mt. House
Posts: 1,829
Default

I had luck with 150g-180g in my last 308win using imr3031 it shot 168g berger classic hunters and hornady 180g btsp very well with that powder
Reply With Quote
  #14  
Old 11-01-2017, 12:13 PM
gtr gtr is offline
Banned
 
Join Date: Nov 2013
Location: Manitoba
Posts: 1,529
Default

Win 748 with 150 grainers, works well for me.
Reply With Quote
  #15  
Old 11-01-2017, 12:18 PM
markg markg is offline
 
Join Date: Jun 2008
Location: Calgary Area
Posts: 2,377
Default Similar

Quote:
Originally Posted by 50BMG View Post
Your first issue might be that brass you're using. Upgrade that and you might see better results. Other than that, here is a load I use on my PGW Coyote.

Barrel length: 24"
Brass: Lapua
Primer: CCI BR2
Powder: Varget 47.2gr
Bullet: Lapua Scenar 155gr
Ogive OAL: 2.230" .007" jump (MY RIFLE, NOT YOURS)
Velocity: 2903fps 5 shot average S.D.=5 E.S.=10

Start low and work your way up. This load is 1/3moa out to 1300m.

EDIT: btw, this is not a hunting load.
I have had similar result with a similar load. Only shot mine out to 600m but the combo of Varget / Lapua/ CCI Br 2 is excellent. I have had similar results with sierra match kings as well. We were shooting clay pigeons or what ever you call them at 500 yards (think they are about 4 inches in diameter). Mine were a little lighter in powder and a bit slower but hyper accurate.
Reply With Quote
  #16  
Old 11-01-2017, 12:21 PM
markg markg is offline
 
Join Date: Jun 2008
Location: Calgary Area
Posts: 2,377
Default Foot Note

We were not throwing the clay pigeons in the air. We placed them on the ground with the orange side facing the shooter.
Reply With Quote
  #17  
Old 11-01-2017, 09:17 PM
Pioneer2 Pioneer2 is offline
 
Join Date: Jan 2008
Posts: 4,336
Default A Gooder.........

Varget
Reply With Quote
  #18  
Old 11-01-2017, 09:23 PM
pkmckee pkmckee is offline
Banned
 
Join Date: Sep 2017
Posts: 31
Default

Still learning,but if varget is not available imr 4320,imr 4064 and h335.
Reply With Quote
  #19  
Old 11-02-2017, 02:13 PM
peakseeker's Avatar
peakseeker peakseeker is offline
 
Join Date: Jun 2010
Location: alberta
Posts: 385
Default

150gr scirrocos, 45.5gr varget, fed 210, rp brass. 168gr smk, 44gr varget, wlr primer, rp brass. 165gr speer grand slam, 45.5gr imr 4064, fed 210gm, rp brass. all shoot really well from my tikka t3.
Reply With Quote
  #20  
Old 11-02-2017, 02:46 PM
PAB270 PAB270 is offline
 
Join Date: Aug 2010
Location: Calgary, AB
Posts: 16
Default

18” bbl
1:10 twist
2.81 COAL
Winchester brass
Federal 210m primer
150gr ttsx
44.5gr varget
Reply With Quote
  #21  
Old 11-02-2017, 06:19 PM
Scottmisfits Scottmisfits is offline
Banned
 
Join Date: Aug 2012
Location: Calgary
Posts: 2,109
Default

Federal brass and 210 primers, IMR4166, and Barnes 165 or 168 grain Triple Shocks worked very well for me. I started to load up 165 grain Sierra Game Kong’s but didn’t get very far in development yet because, you know, life happens and then it’s season. But it’s looking very promising.
Reply With Quote
  #22  
Old 11-02-2017, 06:44 PM
SlightlyDistracting SlightlyDistracting is offline
Banned
 
Join Date: Aug 2017
Posts: 438
Default

Reloader 15 and varget. 4064 in semi autos
Reply With Quote
  #23  
Old 11-02-2017, 07:28 PM
260 Rem 260 Rem is offline
 
Join Date: Nov 2009
Location: East Central Alberta
Posts: 8,315
Default

When Enduron 4166 first came out, I did some side-by-side comparisons with Varget in a consistent 308. Couldn’t say one was better than the other.
__________________
Old Guys Rule
Reply With Quote
  #24  
Old 11-03-2017, 06:03 AM
fps plus fps plus is offline
 
Join Date: Sep 2015
Posts: 1,815
Default

I've had luck with 150-165 gr bullets and imr4320and re15

At present using 15o Barnes ttsx and re-15
Reply With Quote
  #25  
Old 11-03-2017, 07:58 AM
elkhunter11 elkhunter11 is online now
 
Join Date: Dec 2008
Location: Camrose
Posts: 44,828
Default

Quote:
Originally Posted by outdoorguy View Post
I ve picked up a T3 compact in .308 and have been trying to get an accurate load out of it with no consistent success. I have been using fired, tumbled, chamfered, trimmed Rem brass, Fed 210 primer, 46 gr Varget , 165 Nosler ballistic tip and OAL is 2.81. Does any one have some loads that have been accurate with their 308 that you would be willing to share.
I may also switch to 150 gr accubonds as in what I have been reading that appears to be a popular one for hunting.....
Can anyone help out with some information.

Thanks All!
How far are the bullets seated from the lands?
__________________
Only accurate guns are interesting.
Reply With Quote
  #26  
Old 11-03-2017, 08:41 AM
kayaker kayaker is offline
 
Join Date: Dec 2008
Posts: 1,300
Default

I have had very good results with 150gr Speer SPBT, Hornady SPBT and Nolser Ballistic Tips over 45gr Varget, CCI 200 or BR2 primers, Federal brass (apparently junk according to the interwebz?) and seated to 2.8". All shot extremely well out of a Howa heavy barrel and Savage Mod 11. They shoot OK out of my Ruger Scout but it seems to like longer bullets.

150gr Barnes TTSX over 45 gr Varget, 2.8" OAL, CCI 200 or BR2 primer in Winchester brass (more case volume than Fed which helps with the longer monometal bullets) alos shoots well for me. I put a very light Lee factory crimp on these.

In my limited experience with Accubonds (not in .308) they are very user friendly and not particularly sensitive to seating depth, well not as sensitive as some other bullets.
Reply With Quote
  #27  
Old 11-03-2017, 09:45 PM
EZM's Avatar
EZM EZM is offline
 
Join Date: Jul 2010
Location: Edmonton
Posts: 11,851
Default

Quote:
Originally Posted by markg View Post
We were not throwing the clay pigeons in the air. We placed them on the ground with the orange side facing the shooter.
Chuck Norris could have hit them out of the air at 500m using iron sights ...... while fighting off Russians.
Reply With Quote
  #28  
Old 07-10-2019, 07:17 AM
BLR20019 BLR20019 is offline
 
Join Date: Jul 2019
Posts: 1
Default Seating depth

Quote:
Originally Posted by tasco View Post
I am also working on a load for my .308 BLR takedown. It is a challenge trying to find out what a gun likes. Attached is a load test that I did for my BLR. I haven't had time yet to check out the two best velocity nodes. But if you have access to a chronograph, this may be a very fast way for you to come up with a good starting point or load to test. I have posted this graph in another thread. You don't need to go in .3 grain increments like I did. .5 grains should be more than adequate.

Hey mate what’s your overall cartridge length on your hand loads??
Reply With Quote
  #29  
Old 07-10-2019, 08:02 AM
barsik barsik is offline
 
Join Date: Jun 2011
Location: boyle,ab
Posts: 739
Default

finding an accurate load can be frustrating if the rifle has a bit of unwanted bedding pressure. you might want to check your barreled action to stock fit and check the crown before spending money on reloading components.
Reply With Quote
  #30  
Old 07-10-2019, 08:09 AM
Subaru297 Subaru297 is offline
 
Join Date: Jan 2010
Location: Calgary, Alberta
Posts: 70
Default

Quote:
Originally Posted by kayaker View Post
I have had very good results with 150gr Speer SPBT, Hornady SPBT and Nolser Ballistic Tips over 45gr Varget, CCI 200 or BR2 primers, Federal brass (apparently junk according to the interwebz?) and seated to 2.8". All shot extremely well out of a Howa heavy barrel and Savage Mod 11. They shoot OK out of my Ruger Scout but it seems to like longer bullets.
This has been my best load so far as well. I have had a couple <1/2moa groups but need to shoot more to see if this is consistent. It has shot a few ~1" groups as well.
Federal brass
45gr Varget
150gr Speer BTSP
CCI 200 primer
2.83" COAL (Max mag length)

Shoots pretty well out of my T3x and the Speer bullets are cheap!

I have tried the 178gr ELD-X as well and got a decent group but it was a compressed load when seated to mag length.

Cheers
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 07:30 AM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.