Go Back   Alberta Outdoorsmen Forum > Main Category > General Discussion

Reply
 
Thread Tools Display Modes
  #1  
Old 10-13-2019, 12:15 PM
Sooner Sooner is offline
 
Join Date: Mar 2009
Location: Edmonton
Posts: 9,649
Default 60 Gallon Air Tank Pin Hole

So after 30+ yrs of use, I found out my stand up tank has sprung a leak beside the drain cock when I fired it up on Saturday. I know it is from rust(and my bodyman experience tells me the whole bottom is ready to go now so patching is out) and in doing some googling, I realize it is a hazard now, so when I need to fill a tire or use it, I will run it with the drain open so it fills enough to do the job but won't let it pressure up.

I bought good quality back then and it still has a great top end(motor part). Really don't want to or can afford a new compressor.

A welding shop should be able to remove the bottom cap, make something up and weld a new one on? Basically lose the rusty crusty bottom end? Or is that job going to be as costly as a new compressor? Bonus part about this is they can install a big drain valve vs that tiny one it came with.


Anyone have this done? If you know a welder/shop on here in Edmonton and area who I can support, pm me.

thanks
Reply With Quote
  #2  
Old 10-13-2019, 12:36 PM
45/70/500 45/70/500 is offline
 
Join Date: Apr 2010
Location: N/W CALGARY
Posts: 614
Default

100 lb propane bottle works really well for a replacement tank
__________________
Reply With Quote
  #3  
Old 10-13-2019, 01:05 PM
Dean2's Avatar
Dean2 Dean2 is online now
 
Join Date: Dec 2008
Location: Near Edmonton
Posts: 14,971
Default

You can buy the tanks separate for a lot less money than a whole new compressor. An 80 gallon tank is under $300, whereas a good quality compressor would be a couple of thousand at least. That would be the way I would go if the top end is still in good shape. You can often find large tank compressors on Kijiji real cheap, strip off the crap compressor and use the tank.
Reply With Quote
  #4  
Old 10-13-2019, 02:24 PM
Sooner Sooner is offline
 
Join Date: Mar 2009
Location: Edmonton
Posts: 9,649
Default

Quote:
Originally Posted by Dean2 View Post
You can buy the tanks separate for a lot less money than a whole new compressor. An 80 gallon tank is under $300, whereas a good quality compressor would be a couple of thousand at least. That would be the way I would go if the top end is still in good shape. You can often find large tank compressors on Kijiji real cheap, strip off the crap compressor and use the tank.
Thanks for the tip, that would work for me.
Reply With Quote
  #5  
Old 10-13-2019, 02:42 PM
brslk's Avatar
brslk brslk is offline
 
Join Date: Oct 2012
Location: Edmonton
Posts: 2,375
Default

Quote:
Originally Posted by Sooner View Post
Thanks for the tip, that would work for me.
Keep an eye out at Princess auto. I often see 60 and 80 gallon tanks go on sale for around $300 as Ken said. It would cost you more than that to have your current tank repaired.
Reply With Quote
  #6  
Old 10-13-2019, 04:35 PM
Ken07AOVette's Avatar
Ken07AOVette Ken07AOVette is offline
 
Join Date: Dec 2008
Location: Alberta
Posts: 24,072
Default

I have a stand up tank I am not using, you can have it if you want it. There is a motor and compressor on it, but the compressor I am sure is done. I can bring it next time I come to Edmonton if you want.

I will put up pics if you are interested. Its a nice looking red one.
__________________
Only dead fish go with the flow. The rest use their brains in life.


Originally Posted by Twisted Canuck
I wasn't thinking far enough ahead for an outcome, I was ranting. By definition, a rant doesn't imply much forethought.....
Reply With Quote
  #7  
Old 10-13-2019, 05:22 PM
amosfella amosfella is offline
 
Join Date: May 2013
Posts: 3,221
Default

Quote:
Originally Posted by Dean2 View Post
You can buy the tanks separate for a lot less money than a whole new compressor. An 80 gallon tank is under $300, whereas a good quality compressor would be a couple of thousand at least. That would be the way I would go if the top end is still in good shape. You can often find large tank compressors on Kijiji real cheap, strip off the crap compressor and use the tank.
x2. I did one from Princess when they brought the new tanks in. I had to cut the mounting plate and bracket off the old compressor, cut the mounting plate and bracket off the new compressor, and weld the old plate and bracket on the new compressor. Kinda funny, I did all that, dad got a screaming deal on a IR 80 gallon unit, and never used the one I fixed for 2 years... haha

I think it's going into the other shop when I get it cleaned up and get the machine tools set up.
Reply With Quote
  #8  
Old 10-13-2019, 06:14 PM
Kolibri Kolibri is offline
 
Join Date: Mar 2019
Posts: 40
Default

Quote:
Originally Posted by Sooner View Post
Anyone have this done? If you know a welder/shop on here in Edmonton and area who I can support, pm me.
Looks like you solved the problem, repair is a gonna cost way more than buying a new one, and any B pressure welder would likely avoid touching it.
Reply With Quote
  #9  
Old 10-13-2019, 06:49 PM
sourdough doug sourdough doug is offline
Banned
 
Join Date: May 2007
Location: northern AB
Posts: 2,241
Default

Assuming that the OP has his answer, is there anything one can put in the tank to prevent water build up or to slow down rust...I ask this as info for the OP...
Yeah, right....ha
Reply With Quote
  #10  
Old 10-13-2019, 06:50 PM
Ken07AOVette's Avatar
Ken07AOVette Ken07AOVette is offline
 
Join Date: Dec 2008
Location: Alberta
Posts: 24,072
Default

Quote:
Originally Posted by sourdough doug View Post
Assuming that the OP has his answer, is there anything one can put in the tank to prevent water build up or to slow down rust...I ask this as info for the OP...
Yeah, right....ha
Drain it more often you do not want to introduce contaminants
__________________
Only dead fish go with the flow. The rest use their brains in life.


Originally Posted by Twisted Canuck
I wasn't thinking far enough ahead for an outcome, I was ranting. By definition, a rant doesn't imply much forethought.....
Reply With Quote
  #11  
Old 10-13-2019, 06:53 PM
sourdough doug sourdough doug is offline
Banned
 
Join Date: May 2007
Location: northern AB
Posts: 2,241
Default

Quote:
Originally Posted by Ken07AOVette View Post
Drain it more often you do not want to introduce contaminants
Yeah....if I were to install a timed blowdown,
Reply With Quote
  #12  
Old 10-13-2019, 07:00 PM
Ken07AOVette's Avatar
Ken07AOVette Ken07AOVette is offline
 
Join Date: Dec 2008
Location: Alberta
Posts: 24,072
Default

Quote:
Originally Posted by sourdough doug View Post
Yeah....if I were to install a timed blowdown,
smart- the local cabinet maker has one, cool unit
__________________
Only dead fish go with the flow. The rest use their brains in life.


Originally Posted by Twisted Canuck
I wasn't thinking far enough ahead for an outcome, I was ranting. By definition, a rant doesn't imply much forethought.....
Reply With Quote
  #13  
Old 10-13-2019, 07:26 PM
Dewey Cox's Avatar
Dewey Cox Dewey Cox is offline
 
Join Date: Jan 2012
Location: 204
Posts: 5,397
Default

In regards to the suggestion of using a propane tank...

It's my understanding that air tanks are painted inside to resist rust, while propane tanks aren't. (Making them unsafe for compressed air duty)
__________________
"I like to quote my own quotes" ~ Dewey Cox
Reply With Quote
  #14  
Old 10-14-2019, 08:22 AM
Rancid Crabtree Rancid Crabtree is offline
 
Join Date: Oct 2010
Location: Central Alberta
Posts: 691
Default

I don't want to be the guy jumping down people's throat.
But you are seriously underestimating the dangers of a air tank failing.

For fun calculate the volume of air at atmospheric pressure that is held in a air tank at 120 psi. It's unbelievable how much energy is contained in even a small 20 gallon compressor tank.

Discard the old tank, it's absolutely not worth the risk.
Reply With Quote
  #15  
Old 10-14-2019, 08:48 AM
gunluvr's Avatar
gunluvr gunluvr is offline
 
Join Date: Sep 2012
Posts: 1,594
Default

Quote:
Originally Posted by Rancid Crabtree View Post
I don't want to be the guy jumping down people's throat.
But you are seriously underestimating the dangers of a air tank failing.

For fun calculate the volume of air at atmospheric pressure that is held in a air tank at 120 psi. It's unbelievable how much energy is contained in even a small 20 gallon compressor tank.

Discard the old tank, it's absolutely not worth the risk.
X2. An air compressor tank is a certified pressure vessel. Any changes (cutting, welding, etc.) compromises the original engineer's certification.
__________________
Some days you're a bullet; some days you're a gopher.
Reply With Quote
  #16  
Old 10-14-2019, 09:15 AM
Bushrat's Avatar
Bushrat Bushrat is offline
 
Join Date: May 2007
Posts: 6,898
Default

Google "air compressor tank failure images"
Reply With Quote
  #17  
Old 10-14-2019, 09:25 AM
Ken07AOVette's Avatar
Ken07AOVette Ken07AOVette is offline
 
Join Date: Dec 2008
Location: Alberta
Posts: 24,072
Default

Amazon.ca has timed releases for $50
__________________
Only dead fish go with the flow. The rest use their brains in life.


Originally Posted by Twisted Canuck
I wasn't thinking far enough ahead for an outcome, I was ranting. By definition, a rant doesn't imply much forethought.....
Reply With Quote
  #18  
Old 10-14-2019, 11:21 AM
Puma's Avatar
Puma Puma is offline
 
Join Date: May 2007
Location: WMU 214
Posts: 1,816
Default

I have an auto low pressure blow down valve on mine, when the tank gets below 20 psi the valve opens and drains the water etc out of the tank to drain.
Reply With Quote
  #19  
Old 10-16-2019, 03:31 PM
Sooner Sooner is offline
 
Join Date: Mar 2009
Location: Edmonton
Posts: 9,649
Default

Hi all, appreciate the responses. I do keep the drain open but 30 plus years takes it toll. Rust stops for no one lol.


Looks like Princess Auto sells a 60 gallon tank assy less motor for 400 bucks from what I see online. I will swing by a store and see if they have one to look at. Most likely the easiest way to go.


Thanks again
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 11:47 AM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.