|
|
03-05-2021, 09:16 PM
|
|
|
|
Join Date: Feb 2013
Posts: 1,868
|
|
Quote:
Originally Posted by Salavee
All I'm suggesting is using Net pressure Vs Gross (peak) Pressure... very similar to using Gross horsepower vs Net horsepower in an auto engine.Its the Horsepower that gets to the pavement that does the real work. In a firearm, I simply maintain that is the net muzzle pressure that does the real work.. (resulting velocity).. not the gross pressure. The gross pressure is just a figure that can be measured, primarily for safety reasons, as opposed to the measurable true net pressure... or average pressure, for that matter. If the gross pressure is too high, no doubt, there will be an engine or drivetrain failure somewhere along the way.The same principle goes for a firearm.
Now, for the sake of teaching me a lesson for being so stupid for even daring to mention it, will you, or Elk ,school me precisely, on what the problem is with using net muzzle pressures to consistently, and accurately, determine the resulting muzzle velocities.. I'm listening.
|
If by net muzzle pressure you mean average barrel pressure I don’t know why you call it muzzle pressure. But I know from pistol carbine rounds if you load powders of different burn rates to the same velocity the slower powder will require a bigger charge and has more report because of the higher muzzle pressure even for the same speed. Of course the bigger charge has produced more gas for the same barrel volume it’s a bigger bang at the muzzle without producing higher velocity. For some reason the faster charge has accelerated the bullet more efficiently and the higher muzzle pressure of the bigger slower charge means wasted energy not more velocity in this instance
|
03-05-2021, 09:21 PM
|
|
|
|
Join Date: Jan 2014
Posts: 1,169
|
|
There are so many people on here, that are smarter than Sir Issac Newton, I and a few others on here, don't believe that, so we'll keep following his laws, Until your names precede his in the Halls of Science. F x M = A .
__________________
"The further a society drifts from truth, the more it will hate those who speak it."--- George Orwell
There is no way to make something "Idiot Proof" because Idiots are so resourceful.
|
03-05-2021, 09:25 PM
|
|
|
|
Join Date: Jan 2014
Posts: 1,169
|
|
Quote:
Originally Posted by marxman
If by net muzzle pressure you mean average barrel pressure I don’t know why you call it muzzle pressure. But I know from pistol carbine rounds if you load powders of different burn rates to the same velocity the slower powder will require a bigger charge and has more report because of the higher muzzle pressure even for the same speed. Of course the bigger charge has produced more gas for the same barrel volume it’s a bigger bang at the muzzle without producing higher velocity. For some reason the faster charge has accelerated the bullet more efficiently and the higher muzzle pressure of the bigger slower charge means wasted energy not more velocity in this instance
|
At the muzzle, both Muzzle pressure and Average barrel pressure are Equal.
__________________
"The further a society drifts from truth, the more it will hate those who speak it."--- George Orwell
There is no way to make something "Idiot Proof" because Idiots are so resourceful.
|
03-05-2021, 09:36 PM
|
|
|
Join Date: Dec 2008
Location: Camrose
Posts: 46,088
|
|
__________________
Only accurate guns are interesting.
|
03-05-2021, 09:45 PM
|
|
|
Join Date: Mar 2011
Location: Fox Creek
Posts: 3,413
|
|
__________________
Profanity and name calling are poor substitutes for education and logic.
Survivor of the dread covid
Pureblood!
|
03-05-2021, 09:56 PM
|
|
|
|
Join Date: Jan 2014
Posts: 1,169
|
|
Quote:
Originally Posted by Sashi
There are so many people on here, that are smarter than Sir Issac Newton, I and a few others on here, don't believe that, so we'll keep following his laws, Until your names precede his in the Halls of Science. F x M = A .
|
Even I can't get it right
F=MA
__________________
"The further a society drifts from truth, the more it will hate those who speak it."--- George Orwell
There is no way to make something "Idiot Proof" because Idiots are so resourceful.
|
03-05-2021, 10:13 PM
|
|
|
|
Join Date: Feb 2013
Posts: 1,868
|
|
Quote:
Originally Posted by Sashi
At the muzzle, both Muzzle pressure and Average barrel pressure are Equal.
|
Not if the bullet has gone only halfway down the barrel. Your riddles are just too clever
|
03-06-2021, 01:16 AM
|
|
|
Join Date: Sep 2008
Location: Parkland County, AB
Posts: 4,278
|
|
Quote:
Originally Posted by marxman
If by net muzzle pressure you mean average barrel pressure I don’t know why you call it muzzle pressure. But I know from pistol carbine rounds if you load powders of different burn rates to the same velocity the slower powder will require a bigger charge and has more report because of the higher muzzle pressure even for the same speed. Of course the bigger charge has produced more gas for the same barrel volume it’s a bigger bang at the muzzle without producing higher velocity. For some reason the faster charge has accelerated the bullet more efficiently and the higher muzzle pressure of the bigger slower charge means wasted energy not more velocity in this instance
|
As to your pistol carbine powder, the slower powder usually does require a larger charge will require more dwell time in a barrel than will the faster powder. Extend the barrel length a bit and the difference in velocity will become obvious.
Average barrel pressure is not muzzle or exit (net) pressure . I guess that's why its sometimes called exit pressure. I maintain that one can use projected exit pressure to measure muzzle velocity by simply using the net, or exit pressure projections taken at the muzzle just prior to bullet exit. It is equal to, and more consistent than you can get using peak pressure as a MV indicator. Peak pressure is listed in manuals as a guideline regarding safe pressures. That was mentioned, and equal muzzle pressure provides equal muzzle velocity.. that's all I said, but we have been using peak pressures for ever, haven't we ? I wasn't suggesting anyone use exit pressure, it's just a better indicator of MV.. in my opinion. The problem arose on this topic because I didn't mention what area the pressure was measured at when I first posted about equal pressure and equal velocity. Maybe you guys can ease up a bit now.
.
__________________
When applied by competent people with the right intent, common sense goes a long way.
|
03-06-2021, 07:27 AM
|
|
|
Join Date: Dec 2008
Location: Camrose
Posts: 46,088
|
|
Quote:
equal muzzle pressure provides equal muzzle velocity.. that's all I said,
|
Look at the graph, one curve has more than double the pressure at the muzzle, yet the velocity is equal, so pressure at the muzzle does not determine velocity.
__________________
Only accurate guns are interesting.
|
03-06-2021, 08:58 AM
|
|
|
Join Date: Sep 2008
Location: Parkland County, AB
Posts: 4,278
|
|
Quote:
Originally Posted by elkhunter11
Look at the graph, one curve has more than double the pressure at the muzzle, yet the velocity is equal, so pressure at the muzzle does not determine velocity.
|
As you can see , if you wanted to , the velocity curve intersects at that one point for about half a millisecond. The slower curve is still climbing, the faster curve is descending. How long was the barrel ?
As I asked you previously, try and be specific as to just why muzzle pressure is not reliable as a measure of muzzle velocity. I don't require the use of more than one particular powder and barrel length- just as the manuals do for peak pressuure.
If you can't answer that, forget it. It really does't matter anyway..
__________________
When applied by competent people with the right intent, common sense goes a long way.
Last edited by Salavee; 03-06-2021 at 09:09 AM.
|
03-06-2021, 09:16 AM
|
|
|
Join Date: Dec 2008
Location: Camrose
Posts: 46,088
|
|
Quote:
Originally Posted by Salavee
As you can see , if you wanted to , the velocity curve intersects at that one point for about half a millisecond. The slower curve is still climbing, the faster curve is descending. How long was the barrel ?
As I asked you previously, try and be specific as to just why muzzle pressure is not reliable as a measure of muzzle velocity. I don't require the use of more than one particular powder and barrel length- just as the manuals do for peak pressuure.
If you can't answer that, forget it. It really does't matter anyway..
|
It's so obvious, that I can't believe that you can't see it. The muzzle pressure is the pressure at the muzzle, as is shown on the graph.The red curve is showing just over 10,000psi at the muzzle, the blue curve shows close to 30,000 psi at the muzzle, yet both curves result in the same velocity. If the pressure at the muzzle was a true indicator of velocity, then the blue curve would produce more than twice as much velocity as the red curve. It doesn't get any simpler than that. What is similar in both curves, is the area under the curve, but the muzzle pressure most certainly is not even close to being the same.
__________________
Only accurate guns are interesting.
|
03-06-2021, 10:03 AM
|
|
|
Join Date: Sep 2008
Location: Parkland County, AB
Posts: 4,278
|
|
Quote:
Originally Posted by elkhunter11
It's so obvious, that I can't believe that you can't see it. The muzzle pressure is the pressure at the muzzle, as is shown on the graph.The red curve is showing just over 10,000psi at the muzzle, the blue curve shows close to 30,000 psi at the muzzle, yet both curves result in the same velocity. If the pressure at the muzzle was a true indicator of velocity, then the blue curve would produce more than twice as much velocity as the red curve. It doesn't get any simpler than that. What is similar in both curves, is the area under the curve, but the muzzle pressure most certainly is not even close to being the same.
|
The blue line,( charge wt.powder and barrel length unknown) certainly appears to be the best one to use in my books. Still can't see why the blue pressure curve, in itself, is not an accurate way to measure velocity.
If the barrel length on that chart were given, it would be much simpler to determine your position as the pressure curve on the blue line is not completed.
As stated in the graphs disclaimer , that is not a real test, just an exaggerated example. I've seen enough of those.
__________________
When applied by competent people with the right intent, common sense goes a long way.
|
03-06-2021, 10:56 AM
|
|
|
|
Join Date: Jan 2014
Posts: 1,169
|
|
Quote:
Originally Posted by marxman
Not if the bullet has gone only halfway down the barrel. Your riddles are just too clever
|
Now who would put the muzzle halfway down the barrel? If the bullet stopped halfway down the barrel. there would be o pressure on either side still equal.
__________________
"The further a society drifts from truth, the more it will hate those who speak it."--- George Orwell
There is no way to make something "Idiot Proof" because Idiots are so resourceful.
|
03-06-2021, 11:38 AM
|
|
|
Join Date: Dec 2008
Location: Camrose
Posts: 46,088
|
|
Quote:
Originally Posted by Sashi
Now who would put the muzzle halfway down the barrel? If the bullet stopped halfway down the barrel. there would be o pressure on either side still equal.
|
If there was no pressure, how would the bullet get halfway down the barrel?
__________________
Only accurate guns are interesting.
|
03-06-2021, 11:42 AM
|
|
|
|
Join Date: Jan 2014
Posts: 1,169
|
|
Quote:
Originally Posted by elkhunter11
If there was no pressure, how would the bullet get halfway down the barrel?
|
Marksman put it there. Don't you read these posts?
__________________
"The further a society drifts from truth, the more it will hate those who speak it."--- George Orwell
There is no way to make something "Idiot Proof" because Idiots are so resourceful.
|
03-06-2021, 12:16 PM
|
|
|
Join Date: Sep 2008
Location: Parkland County, AB
Posts: 4,278
|
|
Quote:
Originally Posted by Sashi
Marksman put it there. Don't you read these posts?
|
I appears he just scans a couple of times and calls iit a read. He likes to shoot from the hip in almost every instance . I'm guilty of that myself sometimes, but not to the degree he does. All good anyway. At least he perseveres.
__________________
When applied by competent people with the right intent, common sense goes a long way.
|
03-06-2021, 08:01 PM
|
|
|
|
Join Date: Feb 2013
Posts: 1,868
|
|
Quote:
Originally Posted by Sashi
Now who would put the muzzle halfway down the barrel? If the bullet stopped halfway down the barrel. there would be o pressure on either side still equal.
|
Did I say the bullet was stopped? In fact the pressure would be very much higher on the chamber side than at the muzzle
|
03-06-2021, 08:05 PM
|
|
|
|
Join Date: Feb 2013
Posts: 1,868
|
|
Quote:
Originally Posted by elkhunter11
It's so obvious, that I can't believe that you can't see it. The muzzle pressure is the pressure at the muzzle, as is shown on the graph.The red curve is showing just over 10,000psi at the muzzle, the blue curve shows close to 30,000 psi at the muzzle, yet both curves result in the same velocity. If the pressure at the muzzle was a true indicator of velocity, then the blue curve would produce more than twice as much velocity as the red curve. It doesn't get any simpler than that. What is similar in both curves, is the area under the curve, but the muzzle pressure most certainly is not even close to being the same.
|
He is wrong I thought he was confusing himself but he is in denial
|
03-06-2021, 09:56 PM
|
|
|
Join Date: Sep 2008
Location: Parkland County, AB
Posts: 4,278
|
|
Quote:
Originally Posted by marxman
He is wrong I thought he was confusing himself but he is in denial
|
Originally Posted by elkhunter11 View Post
Actually the graph posted was correct, it actually proves that his exit pressure theory is nonsense. The graph proves that his exit pressure theory is nonsense, because while the velocity is identical, for both curves, one exit pressure is more than double the other. Of course he and the other individual with not admit that, they will try and come up some other nonsense to distract attention away from the fact that their own graph proved them wrong.
Cant blame him for that. Most would get confused. Its a made up and exagerated pressure profile, as sated in the disclaimer above the graph.
__________________
When applied by competent people with the right intent, common sense goes a long way.
|
03-06-2021, 10:09 PM
|
|
|
|
Join Date: Oct 2009
Location: Medicine Hat
Posts: 4,425
|
|
Once the bullet leaves the muzzle no amount of force will influence its velocity. But if a bullet is losing velocity upon exit and another is gaining velocity it "may" gain a slight velocity advantage simply due to inertia of the bullet mass. But I highly doubt it.
__________________
Trades I would interested in:
- Sightron rifle scopes, 4.5x14x42mm or 4x16x42mm
especially! with the HHR reticle. (no duplex pls.)
- older 6x fixed scopes with fine X or target dot.
|
03-07-2021, 12:57 AM
|
|
|
Join Date: Apr 2019
Posts: 111
|
|
As I stated earlier the tool to measure velocity is out there it is called a chronograph. We can all afford one that is how we measure velocity. I don't think any of us has the equipment to measure barrel pressures. I don't know why we are discussing it. Quick Load gives pressures but they tell you not rely solely on their info. Every lot of powder is different and every lot of bullets is different. There for there is no certain way to know the pressure your gun is producing from some body elses data. You are only guessing.
|
03-07-2021, 05:28 AM
|
|
|
|
Join Date: Feb 2013
Posts: 1,868
|
|
Quote:
Originally Posted by WildBillG
For what it is worth Elkhunter11 is right different powders at the same pressure give different velocities. Salvee your equal resitance is the barrel not the powders pressure curve. When the big companies test loads it is with the same rifle for all the data per bullet weight. Some companies may change primers while gathering their data but very few.
I too thought it was a brass or case weakness problem with the 6.5x55 but I think it is a few weak rifles. Although I have an old Speer manual that has hotter loads in it for the military rifles than the newer Nosler manual has for modern rifles.
I like the 6.5x55 and wish I knew what pressure the modern rifles are to be loaded to. It should by all rights shoot faster than the 260 Rem and 6.5 CM but load data says no. If we look at that though the 270 Win is loaded to 65000 PSI and the 280 Rem only to 60000 PSI. Why they are loaded in the same kinds of rifles on the same case design.
|
They do publish modern loads for the 6.5x55 its called the 6.5 skan i use it
|
03-07-2021, 05:40 AM
|
|
|
|
Join Date: Feb 2013
Posts: 1,868
|
|
Quote:
Originally Posted by WildBillG
As I stated earlier the tool to measure velocity is out there it is called a chronograph. We can all afford one that is how we measure velocity. I don't think any of us has the equipment to measure barrel pressures. I don't know why we are discussing it. Quick Load gives pressures but they tell you not rely solely on their info. Every lot of powder is different and every lot of bullets is different. There for there is no certain way to know the pressure your gun is producing from some body elses data. You are only guessing.
|
You are right but salavee stated posts back that reality is quickload not facts,check it out, you probably read it too
|
03-07-2021, 06:55 AM
|
|
|
Join Date: Sep 2008
Location: Parkland County, AB
Posts: 4,278
|
|
Quote:
Originally Posted by marxman
You are right but salavee stated posts back that reality is quickload not facts,check it out, you probably read it too
|
C'mon Marxman, just where did I say that QL is reality ? QL is a great program but I never did say it was reality. When it gets proper inputs, it is very accurate and that accuracy is always eventually verified by my Magnetospeed. So yes, I don't argue with it when I require accurate projections on a new load. To me that makes it a reliable projection... not reality. It's also pretty reliable on muzzle pressures as well. I take it that you and Elk don't use it so I understand your doubts. If that is the case, don't knock it 'til you've tried it.
All I've learned throughout this whole cluster is that I used the wrong terminology. I said "equal pressure equals equal velocity." I should have said "equally applied" pressure equals equal velocity. My error, and I accept the blame for that and will accept the subsequent heat you guys have dished out.
When it comes to reading and knocking, try reading all my posts again. I think you will understand my original question, for which I still didn't get answer, and I think you will see what I was getting at.
__________________
When applied by competent people with the right intent, common sense goes a long way.
|
03-09-2021, 09:49 AM
|
|
|
Join Date: Sep 2008
Location: Parkland County, AB
Posts: 4,278
|
|
Here's a little note from Brian Litz. Thought you might be interested.
"The 'equal chamber pressure means equal KE' scaling of MV is a general rule, not exact. Certain practical variables in the real world will cause the relation to not hold exactly. Those variables are things like:
1. When you change bullet weight/length in the same chamber, you're affecting the internal case capacity. In order for the relation to hold, when going to a longer/heavier bullet, you would have to throat the chamber out to allow the same internal case capacity.
2. Bearing surface length. Longer/heavier bullets tend to have longer bearing surfaces which take more energy to engrave which affects the energy balance.
3. There are subtleties to the way powder burns in reaction to the time vs. pressure which will affect things too.
Having said those things, the general rule of thumb is still a good rough estimate. In the case of going from 155's to 185's in the Palma gun, let's say you were getting 3000 fps with the 155's. Your expected velocity with the 185's would be: 3000*sqrt(155/185) = 2746. Now if you load the 185's in the same chamber as the 155's, you'll probably fall short of the 2746.
Regarding your Winchester vs. Lapua brass, I would say that when you've matched velocities in the same barrel, that you've matched pressures. Although it's splitting hairs meaning I don't think the difference would be large."
-Bryan
__________________
When applied by competent people with the right intent, common sense goes a long way.
|
03-09-2021, 06:08 PM
|
|
|
|
Join Date: May 2008
Location: West of Edmonton
Posts: 2,313
|
|
Do you guys know how many times you could have watched Smokey and the Bandit, and Old School already
I have know idea what my Swedes are running for pressure, the T3 lite is 2880fps with 129g accubonds, IMR 7828 and consistently tight. I’m gonna go watch Cannonball Run.
|
03-09-2021, 08:46 PM
|
|
|
Join Date: Sep 2008
Location: Parkland County, AB
Posts: 4,278
|
|
Elk et al.. here is my issue. Because you emphatically stated, among other things, that the (phoney) graph was correct in all aspects ,plus your attempt to make myself and another member look stupid, your reloading credentials went right with it ..out the window. Here are the facts, so take 'em or leave 'em .
The ratio of the case volume to the expanded volume is called the expansion ratio. Making the peak pressure in the larger volume means more total gas is required, and that greater total gas volume keeps pressure up higher as the bullet continues down the bore, thus accelerating it to higher velocity than the same peak pressure, created with less gas by the fast powder will do. Thus, two powders, one fast and one slow, can produce the same peak pressure, but not the same velocity as was indicated in the velocity/pressure profile.
This is why velocity alone can't tell you what the peak pressure was.Muzzle pressure could ,as it is in direct proportion to peak pressure , bore size and barrel length. As the pressure erosion is constant throughout barrel length, it could also accurately predict muzzle velocity.
It's unfortunate, but your responses seem be in direct proportion to your ego.
You can fool some of the people some of the time, but not all the people all the time.
A number of good folks have left this great forum due to that type of attitude from a few members over the years and that's not good. Put your freak'n ego in your pocket and carry on with some of the good stuff you have gleaned over the years. Really, the subject matter of this thread is not important anyway, contrary to the matter of trying to make others appear inferior to you. That's a major PO to some, myself included,. There are a lot of real good, knowledgable folks on here. You are not the only one.
The mods can do as they like with this post. I can live with it either way, but this post had to happen sooner or later under the existing and past circumstances.
Rant over.
__________________
When applied by competent people with the right intent, common sense goes a long way.
|
03-09-2021, 08:50 PM
|
|
|
Join Date: Sep 2015
Posts: 1,872
|
|
Quote:
Originally Posted by Homesteader
Do you guys know how many times you could have watched Smokey and the Bandit, and Old School already
I have know idea what my Swedes are running for pressure, the T3 lite is 2880fps with 129g accubonds, IMR 7828 and consistently tight. I’m gonna go watch Cannonball Run.
|
Can’t decide on popcorn or pizza ?
|
03-09-2021, 09:22 PM
|
|
|
Join Date: Dec 2008
Location: Camrose
Posts: 46,088
|
|
Quote:
Originally Posted by fps plus
Can’t decide on popcorn or pizza ?
|
Definitely pizza!.
__________________
Only accurate guns are interesting.
Last edited by elkhunter11; 03-09-2021 at 09:35 PM.
|
03-09-2021, 09:30 PM
|
|
|
|
Join Date: Dec 2010
Location: My House
Posts: 13,587
|
|
Booze + Keyboards = A quick trip to Crazytown.
Sent from my SM-A705W using Tapatalk
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -6. The time now is 07:48 AM.
|