|
01-08-2012, 06:45 PM
|
|
|
Join Date: Feb 2011
Posts: 909
|
|
Auger problem.
I have a Jiffy White lightining. It usually worked good. But today for some reason the auger stoppped turning when it was alomost throught the ice. I notinced that I left it on half choke, would that have caused it to do that?
|
01-08-2012, 06:47 PM
|
Banned
|
|
Join Date: Oct 2010
Location: Edmonton
Posts: 4,018
|
|
Quote:
Originally Posted by Thundercatcher
I have a Jiffy White lightining. It usually worked good. But today for some reason the auger stoppped turning when it was alomost throught the ice. I notinced that I left it on half choke, would that have caused it to do that?
|
Posable motor not getting enough rpm to turn auger try it again with choke off.
|
01-08-2012, 06:48 PM
|
|
|
Join Date: Jun 2010
Location: Calgary
Posts: 1,347
|
|
Did it restart?
Were are you located?
How thick was the ice?
|
01-08-2012, 06:49 PM
|
|
|
|
Join Date: Feb 2009
Posts: 5,143
|
|
When that happens usually you just need to back off a bit, even pull up slightly.the choke being on even slightly may have been bogging it down a bit. Happens to mine if I don't let it warm up for a minute or so.
|
01-08-2012, 10:19 PM
|
|
|
Join Date: May 2007
Location: Edm.
Posts: 5,213
|
|
Open up the small screw on the gas cap ,to let air in the tank !
|
01-08-2012, 10:31 PM
|
|
|
Join Date: Feb 2011
Posts: 909
|
|
there is no screw in the gas cap. It has small pinhole vents in the cap
|
01-08-2012, 10:45 PM
|
|
|
Join Date: Dec 2011
Posts: 41
|
|
Ive got a jiffy and noticed that it can bog down if I don't let it warm up. Give it a minute or so to run in idle before you burn holes.
|
01-08-2012, 11:17 PM
|
|
|
|
Join Date: Sep 2008
Location: Stony Plain.
Posts: 2,495
|
|
Get rid of it and buy an eskimo.
Andy
__________________
"I must not fear. Fear is the mind-killer. Fear is the little-death that brings total obliteration. I will face my fear. I will permit it to pass over me and through me. And when it has gone past I will turn the inner eye to see its path. Where the fear has gone there will be nothing. Only I will remain."
|
01-08-2012, 11:34 PM
|
|
|
|
Join Date: Feb 2011
Location: Calgary
Posts: 1,769
|
|
Quote:
Originally Posted by Thundercatcher
I have a Jiffy White lightining. It usually worked good. But today for some reason the auger stoppped turning when it was alomost throught the ice. I notinced that I left it on half choke, would that have caused it to do that?
|
Could be one of several things - old age, bad memory, etc.
After it warms up for a minute or so, take the choke off.
|
01-09-2012, 12:53 AM
|
|
|
Join Date: Aug 2011
Location: edmonton
Posts: 81
|
|
the ice is getting harder this time of year.... my eskimo z71 aint chewin like it used to..... and its right new... and still a dream
but watch for the double clutch slippage... new augers trannys need a break in period... if the motor runs and the blade doesnt spin. just turn it off.. and restart.... dont bag it. warm it up
says it in the books that clutch slip may happen in first 2 hours of breakin...
Wait you bought a jiffy... . they dont come with manuals?
|
01-09-2012, 01:12 AM
|
Banned
|
|
Join Date: Mar 2010
Location: on a mishn for fishn.
Posts: 8,790
|
|
poor guy at pine lake last yr im sure blew the trany first hole all the way down tryed to help for a few min told him to get a chain saw oh I know what i forgot it was red and said eskimo on the side. not laughing really im not!!
|
01-09-2012, 08:22 AM
|
|
|
|
Join Date: Jun 2009
Location: Edmonton
Posts: 8,144
|
|
Quote:
Originally Posted by Thundercatcher
I have a Jiffy White lightining. It usually worked good. But today for some reason the auger stoppped turning when it was alomost throught the ice. I notinced that I left it on half choke, would that have caused it to do that?
|
How many holes did you dig and have this problem with?
Sometimes it helps to play around with it a little...dig a couple more holes, adjust the choke (you shouldn't need it on once it's warmed up) and see what happens...y'know...troubleshoot.
Typically it'll get a little stuck when you're breaking through the bottom of the ice. Lift up the auger just a bit (so it's not biting in) and then lower it again while giving it some gas and it should chew through.
__________________
Jay: Mostly harmless...
Time, it makes you old. Experience makes you wise. It's only a fool who judges life by what he sees in other peoples' eyes.
- Strung Out
I may not have gone where I intended to go, but I think I have ended up where I needed to be.
- Douglas Adams
|
01-09-2012, 09:30 AM
|
|
|
Join Date: Jul 2009
Location: Almaty
Posts: 2,032
|
|
Quote:
Originally Posted by yeahright
the ice is getting harder this time of year.... my eskimo z71 aint chewin like it used to..... and its right new... and still a dream
but watch for the double clutch slippage... new augers trannys need a break in period... if the motor runs and the blade doesnt spin. just turn it off.. and restart.... dont bag it. warm it up
says it in the books that clutch slip may happen in first 2 hours of breakin...
Wait you bought a jiffy... . they dont come with manuals?
|
Try new blades - you will be surprised. I thought I bought a bad set for replacement blades (really rough factory edge) but my z71 is back to chewing right through. I guess 100's of holes through dirty prairie ice took its toll on the old blades
AK
|
01-09-2012, 10:04 AM
|
|
|
|
Join Date: Feb 2009
Posts: 5,143
|
|
Quote:
Originally Posted by geezle
how many holes did you dig and have this problem with?
Sometimes it helps to play around with it a little...dig a couple more holes, adjust the choke (you shouldn't need it on once it's warmed up) and see what happens...y'know...troubleshoot.
typically it'll get a little stuck when you're breaking through the bottom of the ice. Lift up the auger just a bit (so it's not biting in) and then lower it again while giving it some gas and it should chew through.
|
yep!!
|
01-09-2012, 11:31 AM
|
|
|
Join Date: Dec 2010
Posts: 290
|
|
There are two scews on the side of the Carb.
The one on the right is the high speed setting.
It determines the power ratio / Fuel when the unit
is under load.
Once you get it set up properly the unit will run fine.
One word of caution. Anything works great in the garage !!
the proper way to set these AV520 Tech. motors is under load
on the ice ... drilling.
Here it is in a nut shell.
Gently turn it in so it is just closed all the way .
turn it back out 3/4 to 5/8 of a turn.
this is your baseline/ starting point. use 1/8 turns either
way to fine tune.
If your having problems after this ... send me a PM and we
can talk about it.
I have a few Carb kits left for the Tech. carbs and one pager instructions
on how to set'm up. .... for Forum Members .
|
01-09-2012, 08:25 PM
|
|
|
Join Date: Feb 2011
Posts: 909
|
|
I put on a new gas cap, works great now
|
01-09-2012, 08:32 PM
|
Banned
|
|
Join Date: Oct 2010
Location: Edmonton
Posts: 4,018
|
|
good to hear
|
01-09-2012, 10:41 PM
|
Banned
|
|
Join Date: Mar 2010
Location: on a mishn for fishn.
Posts: 8,790
|
|
Quote:
Originally Posted by Thundercatcher
I put on a new gas cap, works great now
|
often times it is the simplest fix that works k.I.s.s wins again
|
01-10-2012, 07:49 PM
|
|
|
Join Date: May 2007
Location: Edm.
Posts: 5,213
|
|
Your welcome !
|
01-10-2012, 08:04 PM
|
|
|
Join Date: May 2010
Location: Edmonton
Posts: 1,844
|
|
Just curious.. why would you get a new gas cap???? What was wrong with the old one??? Unscrew the vent sure, but get a new cap?????
|
01-10-2012, 08:11 PM
|
Banned
|
|
Join Date: Oct 2010
Location: Edmonton
Posts: 4,018
|
|
Quote:
Originally Posted by FishingFrenzy
Just curious.. why would you get a new gas cap???? What was wrong with the old one??? Unscrew the vent sure, but get a new cap?????
|
If you read he said it was not a screw vent it was a pin vent they work off pressure and was not working apparently.
|
01-10-2012, 08:24 PM
|
|
|
Join Date: Mar 2011
Posts: 33
|
|
I just finished reading through this thread and I have to admit there is some interesting advise. I think Jiffy 10 nailed the technical advise but maybe all you need to do (which was mentioned a couple of times) is lift up on the auger to allow the blades to turn and slowly (under control) slowly allow the blades to bite until your thru. I own two augers both are jiffy's. It's pretty common to bog out just before you hit water.
|
01-10-2012, 09:42 PM
|
|
|
|
Join Date: Feb 2009
Location: Cochrane, Alberta
Posts: 1,758
|
|
Not to hijack the thread from the OP, but it is a related question:
Where do you get a replacement screw for the vent cap? Mine seemed to have vibrated out...
I have a screw with the right threads in it right now...but it is way too long. I can replace the screw, but where do you get the little tension spring to go with it?
__________________
"You're gonna need a bigger boat!" - Martin Brody, 1975
"There seems to be alot of urinating in breakfast cereal around here." - Rackman, 2010
"It is true, there are dead beat dads out there, and there are thousands of dead beat moms too, who live off the efforts of good men trying to do the right thing." -KegRiver, 2011
"You have social media to thank for turning everyone into self-righteous know-it-alls.." -random internet dude, 2015
|
01-10-2012, 09:54 PM
|
Banned
|
|
Join Date: Oct 2010
Location: Edmonton
Posts: 4,018
|
|
Quote:
Originally Posted by Jack&7
Not to hijack the thread from the OP, but it is a related question:
Where do you get a replacement screw for the vent cap? Mine seemed to have vibrated out...
I have a screw with the right threads in it right now...but it is way too long. I can replace the screw, but where do you get the little tension spring to go with it?
|
I think WSS sells them
|
01-10-2012, 10:51 PM
|
|
|
|
Join Date: Feb 2009
Location: Cochrane, Alberta
Posts: 1,758
|
|
Sweet....thanks, HT!
__________________
"You're gonna need a bigger boat!" - Martin Brody, 1975
"There seems to be alot of urinating in breakfast cereal around here." - Rackman, 2010
"It is true, there are dead beat dads out there, and there are thousands of dead beat moms too, who live off the efforts of good men trying to do the right thing." -KegRiver, 2011
"You have social media to thank for turning everyone into self-righteous know-it-alls.." -random internet dude, 2015
|
01-11-2012, 04:56 AM
|
|
|
|
Join Date: Jan 2010
Location: Edmonton
Posts: 6,470
|
|
Quote:
Originally Posted by Jack&7
Not to hijack the thread from the OP, but it is a related question:
Where do you get a replacement screw for the vent cap? Mine seemed to have vibrated out...
I have a screw with the right threads in it right now...but it is way too long. I can replace the screw, but where do you get the little tension spring to go with it?
|
Try a spring from a pen?
|
01-11-2012, 06:20 AM
|
|
|
Join Date: Jun 2010
Location: Calgary
Posts: 1,347
|
|
That's a great idea
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -6. The time now is 08:43 PM.
|