Lake Field Mark II 22LR
A few years ago my wife was shooting this 22. After firing a round she worked the bolt rearward, the bolt came out in her hand and she said something fell out on the ground. (No, not the empty case). We looked and looked but never found anything. We put the bolt back in and put it in the safe and had not fired it due to obvious situation that just occurred.
With coyote snaring season upon us, I remembered we had this gun and thought it would make a good dispatch gun. But am leery to fire a round. I have worked the action and it feels normal, bolt does not come out or seem loose. Does anyone have any history with failures similar to this or familiar with these rifles? May not be worth the $$ to repair, but its hard to also justify a rifle sitting laying idle. Suggestions? |
The Lakefields are the same as the Savage Mark II rifles. You should be able to find a schematic online that shows the bolt and receiver parts. Compare that to what you have.
|
Quote:
|
Lake Field Mark II 22LR
Here is a good schematic. https://www.gunpartscorp.com/gun-man.../mark-ii-lkfld
Based on your description it is likely the extractor. Western Gun Parts in Edmonton should have what you need once you identify it. |
if it seems to function properly , why not cycle a few rounds through it (in a safe place).....if it cycles properly, why not fire it and see if it works? people have been mistaken..maybe nothing fell out
|
|
Quote:
|
Quote:
|
If the bolt body and hammer (as it's called in the diagram) aren't lined up properly yes, that can happen.
|
Quote:
|
Quote:
|
Quote:
|
Quote:
|
There are two bolt designs ,that I have seen from Lakefield/Savage . The OP has the earlier model ,the schematic link provided shows the current configuration .The earlier uses a pin on each, to locate and lock the extractor /spring and guide/spring in the bolt body. You can see the locater holes in the top pic.
The later uses the "C" clip retainer for the that purpose ,much more user friendly design for cleaning ,disassembly. Lakefield was the Canadian division of Savage Arms ,till they changed the name in the mid 90's. |
Quote:
|
Quote:
|
Quote:
Does anyone have tips for removing the extractor pins for cleaning? I have two that are having extraction problems, and I think they just need a good cleaning. I was unable to remove the pins with the tools I have. |
Quote:
If you are cleaning your extractors, make sure to keep track of which one goes on which side. It won't eject properly if you mix them up. |
Quote:
I thought I'd give you a couple days to figure it out before posting.I have seen the coil springs in these style of bolts so compacted with crud that they were basically solid with no movement what so ever. |
I seem to recall that the ejector which is a stamped piece of steel has a tab on it that prevents the bolt from coming out without the trigger being pulled or something, its is a weak part and breaks allowing the bolt to come out easily, thats probably what the metal piece was...
|
bolt trouble
2 Attachment(s)
Can anyone show me better pictures of the Lakefield Mark 2 bolt. I have this one and I think there is a piece broken or wore off of it. When replacing bolt into rifle the guide lug?just does not line up after pulling bolt to rear.
Any help would be great. |
better pics
2 Attachment(s)
Here is better view of my problem I believe
|
So does no one have any help with this?Trying to fix it for a really well behaved teen kid.
|
since the op, i happened to acquire one of these .22's. (as an aside, i have never owned any type of gun with a worse trigger!)
.....anyway, mine can be a little tricky to get the bolt all lined up so that it will fit in properly. a little messing with it will get it done. first, i insert the bolt with the flat face to the bottom (duh), then when it goes in and won't finish dropping in, i twist on the back portion of it until the pin lines up with the channel and viola, pull the trigger and in she goes. ps, tigertrainer, how did you get the back of the bolt to stay out like that? my suspicion is that something must be broken inside or it would definitely be tight against the back of the bolt because of the spring pressure inside. mine will certainly not stay out like that and i don't think it should if everything is right. this litttle gun is reminds me of a piece of agriculture equipment compared to a european auto. man for rough.......but does the little bugger ever shoot if you can do your part with the awful trigger. btw, does anyone have any advice on tuning the trigger.......or can an after market one be obtained (i looked but couldn't find one for it) |
bolt trouble
don't know what you mean by back of bolt staying out.I have it all apart and would like to see some close ups of another bolt. I think a piece is broken off mine. The little nub on it.
|
Must be 15 years since I sold my Mark II but what you are missing is #9
Extractor Clip. You can see in both pictures of your bolt shiny line were this thin black flat 6-7 mm wide piece was rubbing on your bolt. Notice that nothing is holding extractors now in their channels. Your wife was right. Andrew |
KBF -mine looks just as yours. Took a few minutes to get all lined back up right when trying to install the bolt. That seem normal?[/QUOTE]
Oops I did not notice that this is Chargerguy bolt picture but you (KBF) admitted that yours look the same way. IMO You both missing the Extractor clip. KBF You can fire your 22 but have a cleaning rod ready to push the empty shell out of the chamber. |
1 Attachment(s)
Quote:
|
Quote:
|
Quote:
|
All times are GMT -6. The time now is 06:29 PM. |
Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.