Resharpening Auger Blades
Anyone have luck in resharpening auger blades? Mine are off of an 8” Ion electric. I already replaced the blades and was planning on taking the used set in to a shop to get them resharpened but was told by another outdoorsmen that they are “laser sharpened” and sharpening will not be successful. Who’s tried it? Thanks Ken
|
I thought I could sharpen them myself also and miserably failed and ended up buying a new set. Some guys have mentioned on here that they have been successful in sharpening them but I think many have mentioned that they take them to a shop to get sharpened. they way they sit on the auger I think that they have to be sharpened precisely with the angle that they sit on, too much and they will cut too hard and not enough and they wont cut at all.
|
I have the same auger (Ion 8") and just finished doing mine with my Lansky. The 30* profile on the Lansky matched the auger blade profile perfectly. Tried them out the other day and they cut like new.
I took my time and had to get a couple nicks out but it seemed to work well. |
For the average guy....Sharpen the top edge only. The bottom edge (the edge that sits on the ice) is best left alone. Top edge only and sharpen unill you can feel a slight burr form Leave the burr there, resist the urge to knock it off from the bottom edge. Go cut your holes and the burr will fall off. This is the most fool proof way of sharpening auger blades but still requires some knowledge and skill on sharpening steel.
|
I got a auger blade sharpener from the fishing hole, twice a season I run it over the blades and It works pretty good
|
I have had good luck in Calgary at carbide saw services Ltd in Bowness
|
I've been taking my blades to R & R Sharpening on the west end of Edmonton. Done this the last 3-4 years and it's been great.
|
Any recommendations for a self sharpening system(eg. Lansky) that can be purchased for the Strikemaster Lazermag blades or is a guy better off to take them to a sharpening shop as has already been mentioned?
|
I tried sharpening mine and it didn't work. The blade itself was sharp but if its not the exact angle that it is supposed to be it won't cut at all. Now I just treat the blades as being disposable.
|
take mine too the local skate sharpener:test:
great job last for years:sHa_shakeshout: just tell them its for a auger :character0053: Food for thought David:) |
Any recommendations for good auger blades sharpening outfits in the Sherwood Park area, thanks.
|
If you know what you are doing a belt sander, or even sand paper on a piece of glass and buffing wheel will touch up your blade to razor sharp very quickly. Lansky diamond stone will work too but you must work very carefully and slowly to ensure you keep the exact angle over the whole edge.
Never sharpen the bottom and make sure you keep the exact top angle. You can also use shims to offset changes in the angle that sometimes occurs due to sharpening or from dropping the auger on its cutting edge and bending the wings. |
https://www.thefishinhole.com/index....ENER/&se=26328
If u have a jiffy u could buy this. Sharpens at right angle . No idea if they work for other auger brands. |
R&R Sharpening (Edmonton)
Quote:
Therefore I have to give a positive shout out for R&R Sharpening. Had my stealth stx 10” done last week after I got back and now it drills like a hot knife through butter. Had my doubts when I picked it up as I noticed they sharpened the bottom of the blade not the top as I expected. I was assured by the staff it was done correctly and to their credit it worked exactly as they promised and much, much better than I expected. Just like new again. Great price too. $15.75 (GST included). Dropped it off Monday at noon and was called Tuesday at 4pm that it was ready. Less than the $95 for a new set of blades that I bought “just in case”. Oh well, I have a spare set now. 10734 - 178 st Edmonton :happy0034: :happy0034: (2 thumbs up!) |
Quote:
|
Quote:
|
Quote:
|
Foothills sharpening right outside of Okotoks is my go to Guy for sharpening all my blades. $8.00 per blade and great customer service. They even sharpened my point for free....
|
Might give this method a try when my blades get dull again. I think it’s worth a try anyway .
https://m.youtube.com/watch?v=ehItnNqI_7k |
Auger Blades
Did up 3 sets of 10" Eskimo power auger blades this am with a 1"x3" Norton stone,but might have to try the buffing wheel and see if it is as good.
|
Agree With Carbide
Quote:
|
Ive always done my at home with a lansky. Use the steepest edge angle and giver.
Been working for years. |
Quote:
|
Quote:
|
Just put a fine stone to mine last night ,
|
Quote:
|
All times are GMT -6. The time now is 12:32 PM. |
Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.